Effect of finish-line curvature on the marginal and internal adaptation of Co-Cr copings fabricated by selective laser melting

Authors

  • Gaby Oliveira Ruiz Universidad Peruana Cayetano Heredia. Lima, Perú.
  • Cecilia del Pilar Portocarrero Claros Universidad Inca Garcilaso de la Vega. Lima, Perú.
  • Jossep Mauro Gómez Alarco Universidad Católica de Santa María. Arequipa, Perú.
  • Martin Gilberto Quintana Del Solar Universidad Peruana Cayetano Heredia. Lima, Perú. https://orcid.org/0000-0002-7087-7874

DOI:

https://doi.org/10.20453/reh.v36i3.8209

Keywords:

dental marginal adaptation, dental crowns, computer-aided design, dental alloys, three-dimensional printing

Abstract

Objective: To compare the effect of three finish-line curvatures on the marginal and internal fit of cobalt-chromium (Co-Cr) metal copings fabricated by selective laser melting using master models with maxillary first premolar anatomy. Materials and methods: An in vitro experimental study was conducted. Three Co-Cr master models of a maxillary right first premolar were fabricated with finish-line curvatures of 0.5, 1.5, and 2.5 mm. Thirteen Co-Cr copings were fabricated for each group using selective laser melting (n = 39). Marginal and internal fit, including axial and occlusal gaps, was evaluated using the silicone replica technique under a stereomicroscope at ×40 magnification. Data were analyzed using the Kruskal-Wallis test, Mann-Whitney U test, and ANOVA, with a 95% confidence level (p < 0.05). Results: Marginal discrepancy was 87.02 ± 24.89 µm for the 0.5-mm curvature, 93.55 ± 14.45 µm for the 1.5-mm curvature, and 93.07 ± 11.71 µm for the 2.5-mm curvature, with significant differences among the groups (p = 0.003). The 0.5-mm curvature showed a lower marginal discrepancy than the 1.5-mm (p = 0.0052) and 2.5-mm (p = 0.002) curvatures. No significant differences in axial internal fit were found among the groups (p = 0.3397). In contrast, occlusal internal fit showed significant differences (p < 0.0001), with mean discrepancies of 228.21 ± 31.05 µm, 201.27 ± 17.62 µm, and 194.80 ± 19.93 µm for the 0.5-, 1.5-, and 2.5-mm curvatures, respectively. Conclusions: The 0.5-mm curvature showed the lowest marginal discrepancy, whereas the 1.5- and 2.5-mm curvatures showed lower occlusal internal discrepancies than the 0.5-mm curvature. No statistically significant differences were observed in axial internal fit.

Downloads

Download data is not yet available.

Author Biographies

Gaby Oliveira Ruiz, Universidad Peruana Cayetano Heredia. Lima, Perú.

Especialista en Rehabilitación Oral.

Cecilia del Pilar Portocarrero Claros, Universidad Inca Garcilaso de la Vega. Lima, Perú.

Especialista en Rehabilitación Oral.

Jossep Mauro Gómez Alarco, Universidad Católica de Santa María. Arequipa, Perú.

Magister en Estomatología

Martin Gilberto Quintana Del Solar, Universidad Peruana Cayetano Heredia. Lima, Perú.

.

References

Yu N, Dai HW, Tan FB, et al. Effect of different tooth preparation designs on the marginal and internal fit discrepancies of cobalt-chromium crowns produced by computer-aided designing and selective laser melting processes. J Adv Prosthodont. 2021;13(5):333-42. doi:10.4047/jap.2021.13.5.333

Gholamrezaei K, Vafaee F, Fathi Afkari B, et al. Fit of cobalt-chromium copings fabricated by the selective laser melting technology and casting method: a comparative evaluation using a profilometer. Dent Res J [Internet]. 2020;17(3):200-7. Disponible en: https://www.ovid.com/jnls/derj/fulltext/01439444-202017030-00006~fit-of-cobalt-chromium-copings-fabricated-by-the-selective

Alqahtani AS, AlFadda AM, Eldesouky M, et al. Comparison of marginal integrity and surface roughness of selective laser melting, CAD-CAM and digital light processing manufactured Co-Cr alloy copings. Appl Sci. 2021;11(18):8328. doi:10.3390/app11188328

Sarda AS, Bedia SV. Influence of manufacturing technique on marginal fit of cobalt chromium restorations: an in-vitro Study. Indian J Dent Res. 2021;32(4):495-9. doi:10.4103/ijdr.ijdr_1075_20

Yang J, Li H, Xu L, et al. Selective laser sintering versus conventional lost-wax casting for single metal copings: a systematic review and meta-analysis. J Prosthet Dent. 2022;128(5):897-904. doi:10.1016/j.prosdent.2021.02.011

Revilla-León M, Özcan M. Additive manufacturing technologies used for processing polymers: current status and potential application in prosthetic dentistry. J Prosthodont. 2019;28(2):146-58. doi:10.1111/jopr.12801

Flores YE, Loarte MY, Zelada CC, et al. Adaptación de cofias metálicas confeccionadas con dos técnicas: cera perdida colada por centrifugación convencional y fusión selectiva por láser. Rev Estomatol Herediana. 2017;27(2):88-96. doi:10.20453/reh.v27i2.3139

Holmes JR, Bayne SC, Holland GA, et al. Considerations in measurement of marginal fit. J Prosthet Dent. 1989;62(4):405-8. doi:10.1016/0022-3913(89)90170-4

Sarafidou K, Chatziparaskeva M, Chatzikamagiannis D, et al. Evaluation of marginal/internal fit of fixed dental prostheses after digital, conventional, and combination impression techniques: a systematic review. Eur J Oral Sci. 2022;130(6):e12902. doi:10.1111/eos.12902

Zelada CC, Flores YE, Loarte MY, et al. Adaptación de cofias unitarias en Co-Cr elaboradas con diferentes técnicas de fabricación y sobre dos líneas de terminación. Rev Estomatol Herediana. 2018;28(1):7-15. doi:10.20453/reh.v28i1.3278

Sakornwimon N, Leevailoj C. Clinical marginal fit of zirconia crowns and patients' preferences for impression techniques using intraoral digital scanner versus polyvinyl siloxane material. J Prosthet Dent. 2017;118(3):386-91. doi:10.1016/j.prosdent.2016.10.019

Çin V, İzgi AD, Kale E, et al. Marginal and internal fit of monolithic zirconia crowns fabricated by using two different CAD-CAM workflows: an in vitro study. Prosthesis. 2023;5(1):35-47. doi:10.3390/prosthesis5010003

Abdullah FR, Mafri TA, Shen YK. Principles, current applications, and future perspectives of selective laser melting in prosthodontics: a review. Metals. 2026;16(4):415. doi:10.3390/met16040415

Limpuangthip N, Hlaing NH, Lee SJ, et al. Factors affecting the fit of metal-based restorations fabricated by selective laser melting: a systematic review. J Prosthet Dent. 2026;135(5):e29-42. doi:10.1016/j.prosdent.2025.10.045

Joda T, Ferrari M, Gallucci GO, et al. Digital technology in fixed implant prosthodontics. Periodontol 2000. 2017;73(1):178-92. doi:10.1111/prd.12164

Peng CC, Chung KH, Yau HT, et al. Assessment of the internal fit and marginal integrity of interim crowns made by different manufacturing methods. J Prosthet Dent. 2020;123(3):514-22. doi:10.1016/j.prosdent.2019.02.024

Asavapanumas C, Leevailoj C. The influence of finish line curvature on the marginal gap width of ceramic copings. J Prosthet Dent. 2013;109(4):227-33. doi:10.1016/s0022-3913(13)60049-9

Tao J, Han D. The effect of finish line curvature on marginal fit of all-ceramic CAD/CAM crowns and metal-ceramic crowns. Quintessence Int [Internet]. 2009;40(9):745-52. Disponible en: https://www.quintessence-publishing.com/deu/en/article/840177

Kim EH, Lee DH, Kwon SM, et al. A microcomputed tomography evaluation of the marginal fit of cobalt-chromium alloy copings fabricated by new manufacturing techniques and alloy systems. J Prosthet Dent. 2017;117(3):393-9. doi:10.1016/j.prosdent.2016.08.002

Kaleli N, Ural Ç, Us YÖ. Evaluation of marginal discrepancy in metal frameworks fabricated by sintering-based computer-aided manufacturing methods. J Adv Prosthodont. 2020;12(3):124-30. doi:10.4047/jap.2020.12.3.124

Di Fiore A, Zuccon A, Carraro F, et al. Assessment methods for marginal and internal fit of partial crown restorations: a systematic review. J Clin Med. 2023;12(15):5048. doi:10.3390/jcm12155048

Published

2026-09-27

How to Cite

1.
Oliveira Ruiz G, Portocarrero Claros C del P, Gómez Alarco JM, Quintana Del Solar MG. Effect of finish-line curvature on the marginal and internal adaptation of Co-Cr copings fabricated by selective laser melting. Rev Estomatol Herediana [Internet]. 2026 Sep. 27 [cited 2026 Nov. 16];36(3):e8209 . Available from: https://revistas.upch.edu.pe/index.php/REH/article/view/8209

Issue

Section

ORIGINAL ARTICLES

Most read articles by the same author(s)